News from Schwing Bioset

Heat Integration – Opportunities and Concerns

 

Written by Joe Scholl, February 11, 2016

The word “heat” may be defined as the amount of energy that is transferred from one system to another, typically via a temperature differential or “gradient,” and the amount of heat something possesses may be stated in terms of British Thermal Units (BTU), Joules (J), calories (cal), etc. (as compared to reference temperature or datum state).  Measured over time, heat becomes energy that is used to accomplish tasks, and that energy may be measured in BTU/hr, J/sec, etc.  There is a definite cost to energy usage, as evidenced by any plant’s energy utility bill.  As such, there is a high emphasis nowadays in energy re-use (“heat integration”) via applying “waste” heat from one process to another process needing energy.  While many such heat/energy integration techniques may be easily accomplished, there may, under certain circumstances, be limitations to the extent such energy re-utilization efforts may be accomplished.

Many municipal wastewater treatment plants (WWTP’s) are utilizing anaerobic digestion systems and these processes may produce digester gas or “biogas” (chiefly methane and carbon dioxide with other trace chemical constituents and/or contaminants).  The biogas produced may be used by a variety of means, such as for maintaining heated conditions in the digester units and/or in gas engines that drive generators to produce electricity in a combined heat and power cycle (CHP).  These CHP processes generally produce two “waste” heat streams by which heat may be extracted and re-utilized (i.e. “integrated”) in another process.  These two streams are the exhaust (or “stack”) gas from the biogas combustion process itself and a hot water stream (typically a water/glycol mixture) or steam produced from using cooling water to maintain reasonable CHP engine temperatures. 

The extent to which these particular waste heat sources can be utilized depends on many factors, including the costs associated with purchasing, installing, and operating the heat recovery equipment.  With respect to utilizing a waste heat source in a sludge thermal drying operation, some of these factors may include:

  • How close to the drying system is the heat source? Specifically, what are the fluid movement costs from point A to point B, in terms of liquid pumping or gas handling requirements and how does this impact the overall heat integration strategy?  
  • What is the additional capital expenditure (“Capex”) requirement to install insulated piping or ducting from the source to the drying system and are these Capex requirements so high that the payback to incorporate the waste heat into the drying system result in an unreasonably long payback period? 
  • Are long-term corrosion issues a concern, such as materials of selection for digester gas piping, stack gas ducting, etc. (especially if “acid gases” condense-out of the gas stream upon cooling, leading to corrosive conditions within the piping, ducting, or heat transfer equipment) and, if so, what is their Capex impact, as well operating expense (“Opex”) impact (e.g. will long-term corrosion issues require long-term maintenance expenses)? 
  • How much heat will the waste heat stream lose from point A to B and will this heat loss drive the heat recovery economics toward an unfavorable overall result? This point is particularly important if the waste heat stream is steam, where the latent (or condensing/phase change) heat of the steam is the primary (or desirable) heat transfer mechanism.  For example, if the waste steam loses sufficient energy in transit from its source to the drying system, will the steam lose so much heat that it condenses to liquid form, thereby “robbing” the heat integration scheme of the steam’s latent/condensing heat prior to the drying system (noting that the latent/condensing heat of steam is significantly higher than the specific heat capacity of either the steam or liquid forms)?

In general, there are many possibilities for incorporating waste heat into a thermal drying process.  However, the costs (in terms of Capex and Opex considerations) to incorporate the heat integration step must also be considered to determine whether doing so is practical. 

To learn more about waste heat integration strategies and our Fluid Bed Drying Technology, please contact a Schwing Bioset Regional Sales Manager by calling 715-247-3433, email us, and/or visit our website here.

 

Below is just one example of numerous heat recovery possibilities.

Schwing Bioset Stack Gas Heat Integration Schematic

  

Tags: Fluid Bed Drying, Wastewater Treatment, Heat Integration, Energy Re-Use, Heat Recovery